Pile To Bearer Fixing Nz, Home Shop Building & Hardware Hardware Fasteners & Fixing Brackets & Connectors Pile Bearer & Subfloor Kits PBK12S allows ANCHOR/BRACED Pile to be in line with and same height as other piles. Mitre 10 In Trade Magazine - February 2014 Joist fixings Joist fixings to piles or bearers are in NZS 3604: 2011 6. Connection detail covers both Anchor and Braced Piles, with bearer sizes Both these products comply with NZS 3604:2011 as a fixing method for timber piles to bearers to joists. The 12kN product pack is suitable for both Anchor and Brace pile situations whilst the 6kN pack is The 6kN pack is used with cantilever piles. • Suitable for sea spray zone All subfloor construction must be in accordance with NZS 3604:2011NZS. Milsons range of Pile Fixing Kits includes the12kN Pile Fixing Kit, 12kN Retro Pile Fixing Kit, and 6kN Pile Fixing Kits. Place the . NZS 3604 requires lines of lateral support to floor joists within 300 mm of bearer or bracing lines, refer to clause 7. 4613 All subfloor construction Comply with NZS 3604:2011 as a fixing method for timber piles to bearers to joists All packs are supplied inclusive of all necessary nails. 6kN Pile to Bearer Connection Kit 304 Stainless Steel 2 x JVPC80 Brackets, 2 x JVPC40 Brackets and 28 Tek screws. 6kN Pile Fixing Kit Use For Anchor Piles And Bracing Piles The 6kN Pile Fixing Kit should be installed in accordance with this leaflet. All components supplied as one complete package for 12 kN Horizontal Capacity Fixing of Bearer to Comply with NZS 3604:2011 as a fixing method for timber piles to bearers to joists All packs are supplied inclusive of all necessary nails. 6: • If the brace is connected to the When fixing the bearers check the level of the bearer and if required pack with malthoid, or notch over the pile. Visit your local store for the widest range of products. Simplify foundation connections with JVICE's pile to bearer kits. 12 of the LUMBERLOK 6kN Pile Fixing Standard Bearer Kit is designed to securely connect timber piles, bearers, and joists in subfloor construction. All Kits are available in 304 Stainless Steel. All subfloor construction must be in accordance with NZS ECKO 6kN Pile Fixing is designed and tested to adhere to NZS3604:2011 requirements for cantilever pile connections (pile-to-bearer and bearer-to-joist). 8. These comply with NZS 3604:2011 as a fixing method for timber piles to bearers to joists Packs are supplied inclusive of Comply with NZS 3604:2011 as a fixing method for timber piles to bearers to joists. The brackets are Grade 304 Stainless Sub Floor Fixing Kits PBK6/S - Pryda Pile Bearer Kit 6KN Stainless SteelPBK12/S - Pryda Pile Bearer Kit 12KN Stainless Steel BHX6KN - Fortress Pile Bearer Kit This kit allows a cantilever pile to be in line with and the same height as other piles. 4613 All subfloor construction Concrete piles and bearer fixing Options for ordinary piles While concrete piles are not commonly used, NZS 3604:2011 Timber-framed buildings permits them provided the height of the pile does not Place the joists against the inside face of the corner piles and bolt them with 12 mm bolts and x 50 x 3 mm washers (diagram 5). The 12kN product pack is suitable for both Anchor and Brace pile situations. At building corner where fixing to boundary joist is precluded fix cleats to next two closest joists along bearer. Test Ref. Suitable for both anchor Nailon Plate 1mm x 160mm long Fixed with 8 x 45mm Nails per end (ex 12kN Pile Fixing Pack) No Nails within 18mm of timber edge Nail on cleats fix to two joists closest to pile. Complete solutions that ensure structural integrity and faster installation. 6kN & 12kN Pile Fixing Kit Product Fixing Guide Key Feature: All screw fixed, ensuring easy and fast installation No need to shave pile to fit bearer All 12kN Pile Fixing Pack - 3 minutes to install the entire kit! • All screws are 14g x 44mm SS Grade 316 Hex Head Screws. Connection detail covers bearer sizes up to 200mm deep, joists up to 250mm Bot Verification Verifying that you are not a robot Connection detail covers both Anchor and Braced Piles, with bearer sizes up to 200mm deep, joists up to 250mm deep. PBK12S Kit Connection detail covers bearer sizes up to 200mm deep, joists up to 250mm deep. FEATURES All components supplied 12kN PILE FIXING FOR BRACED PILES OR ANCHOR PILES The 12kN Pile Fixing must be installed in accordance with this brochure Auckland University Tested. If the piles have been set accurately this adjustment should be no more than a few 6kN PILE FIXING FOR CANTILEVER PILES 10/2011 The 6kN Pile Fixing must be installed in accordance with this brochure Auckland University Tested. At the middle bearer and string r, fix with two 100 x 4 mm nails. Find LUMBERLOK 12kN Pile Fixing Standard Hot Dip Galvanised 12KN at Bunnings. xoigqpdfeimmogzzo1ilulg8ammg0wgxnystzm69nt1owqgzapbgucx